How easily does the movement corrode in a modern Rolex?

[Green Sub]

How easily do the components of a modern Rolex movement corrode?

I'm thinking fresh water intrusion.

Are the metals high carbon? Or more rust resistant stainless steel, anodized aluminum, and brass?

Vanessa, I hope your reading this :thumbsup:

[Vanessa]

I'm right here!

The movement can rust within hours... Depending on "water" damage or "moisture" damage... If your watch crystal only fogged up, it could be not that bad, but if you got a stream of water inside your watch (any type of water will do) your watch will most likely have extensive corrosion.
The only way to salvage it, it by sending it in ASAP! Or taking it in to a watchmaker. But if there is rust, the watchmaker will have to send it to RSC anyways, because we cannot get all the parts that can be affected by water.
Good luck, and please keep me posted!

[dsimon9]

We are the internal components so sensitive to corrosion? Is it a matter money savings, or is it that the materials ideal for the movements also happen to be insensitive to moisture?

Dex

[Green Sub]

I'm right here!

Good luck, and please keep me posted!

Luckily, this hasn't happened to me recently, BUT it did happen to my 1986 TT mid-size DJ with synthetic sapphire crystal around 1998. It was only a "fog-up" of the crystal from a shower where I did not have the twin-lock crown screwed down. The repair costs from the Dallas RSC were not that much above the normal service fee.

What brings this to my mind is the DJ is kinda retired due to my 2 recent Rolex purchases and it hasn't had service since the 1998 fog-up repair and service. It is on a watch winder.

I am considering sending it in for service 1 more time before setting it aside as an heirloom. The watch keeps good time, but I'm just wondering if that water intrusion in 1998 may not make it worth it to service. The original cost of the DJ was $1,995 in 1986.

Thanks so much for replying and you are one great asset to this forum.

[BiG JeEzY]

Just to add, if there is water or moisture in the watch, it is best to keep it away from too much exposure to oxygen. In this case oxygen is the movement's worst enemy as it just accelerates the rusting process and damages the movement even further. It can be so bad that the whole movement would have to be overhauled which could cost a couple thousand dollars!

The best way to slow down the oxidation process, is to leave the watch in a AIRTIGHT ziplock bag or any bag of that variety. Keep the watch in that airtight bag as you send it in for service. Having the crown open may help some of the moisture escape from the watch too as its in the bag.

[entropydave]

Hmmm.... I am curious as to how under normal circs, even with the crown out, water can get in. My understanding was that they were waterproof to 30m even with the crown unscrewed.

[sherwin]

bollocks waterproof to 30m, my understanding is only triplock has that sort of protection... i took a shower with my crown out and water went in as if i had submurged it in water.

[JJ Irani]

I'm right here!

The movement can rust within hours... Depending on "water" damage or "moisture" damage... If your watch crystal only fogged up, it could be not that bad, but if you got a stream of water inside your watch (any type of water will do) your watch will most likely have extensive corrosion.
The only way to salvage it, it by sending it in ASAP! Or taking it in to a watchmaker. But if there is rust, the watchmaker will have to send it to RSC anyways, because we cannot get all the parts that can be affected by water.
Good luck, and please keep me posted!

Smart girl, Vanessa.....thank you!! :clap::clap::chuckle::chuckle:

[scottschoe]

bollocks waterproof to 30m, my understanding is only triplock has that sort of protection... i took a shower with my crown out and water went in as if i had submurged it in water.

With the crown out, there is still a bit of water resistance - don't know how much, never cared to test it. Washing hands with the crown out would probably be fine.

[pwrslider]

My Expy II crown gasket was a bit worn...got some salt water in and it fogged up the dial / crystal......had to change out the dial and hands....the hands corroded badly....and the lume started to fall out.

Now it's true that it took 5 yrs for this to happen...but I never thought it would be an issue.....ooops!

Here the link to my initial post

http://rolexforums.com/showthread.php?t=35940

[Baptistman]

Simple answer, don't wait to find out, get it serviced regularly, and always insure the crown is screwed down. Simple as

[SPACE-DWELLER]

Hmmm.... I am curious as to how under normal circs, even with the crown out, water can get in. My understanding was that they were waterproof to 30m even with the crown unscrewed.

As Jon states, if you make sure that the seals and gaskets are exchanged regularly, you'd not run into that problem. If you have a diver's watch and often dive with it, seals and gaskets should be exchanged every ~ 1½ years. Under normal wearing conditions exchange of gaskets and seals is not necessary before the watch gets serviced every ~ 5th. year.

bollocks waterproof to 30m, my understanding is only triplock has that sort of protection... i took a shower with my crown out and water went in as if i had submurged it in water.

I guess you took the advice to wash your Rolex too literally. :chuckle:

[directioneng]

Well Bo,


IMO
If you changed the gaskets every 1.5 years your Rolex would either be going to or coming back from your RSC and you WOULD NOT BE ENJOYING OWNERSHIP.
Enjoy wearing your Rolex and don't worry too much about the water resistance unless , of course, you are diving to 300 metres every day.

[sherwin]

With the crown out, there is still a bit of water resistance - don't know how much, never cared to test it. Washing hands with the crown out would probably be fine.
i was having a shower which made me think, the pressure is about same as washing hands, so it should be ok even if i had accidentally left it open.

Prior to that, I was swimming and with the crown locked, it was tight as usual. Even though the last service was exactly 7yrs ago

(...)
I guess you took the advice to wash your Rolex too literally. :chuckle:

It is not a habit to wear my watch whilst at home. I usually have a habit of taking my watch off even to wash my hands :agree:, but ovbiously I didnt want to remove my watch for fear that it might be dropped onto bathroom marble

[Tools]

While there is some brass and sometimes the bridges and main movement framework can be plated, the majority of small parts in a watch are freshly machined steel.

That fresh virgin metal will begin to rust if left exposed to the air, so if seals are compromised, just the ambient air entering the watch could have enough moisture content to start the rust process.

If water gets in the case, these parts will start the oxidation (rust) process almost immediately.

Here are a few parts from inside an Omega and you can see a brass center wheel, but the pinion, gears, and pallet, etc. are steel.
http://i198.photobucket.com/albums/aa67/LD_album/Shop/OmegaPartscopy.jpg

[CPTL]

Just to add, if there is water or moisture in the watch, it is best to keep it away from too much exposure to oxygen.

So that's simple enough. If water gets in the case of your Rolex, immediately blast yourself into outer space. No O2, no rust!!

[Toxicant]

I went swimming in the gulf of Mexco and when I got out I checked the time and the whole watch was full of water. I screwed the crown down and took it up to the condo and opened up the crown again and put it in a glass of water. Waited until no more bubbles and removed it from the water and shook it until nothing more came out, did that about 20 times.

Then I took the watch down to my car and pulled a vacuum line off my engine and pushed it over the crown and let the engine suck all the water out. The next day the crystal was cloody so I popped it in the freezer overnight and the next day it was fine :lol:

When I got home and had it serviced the watch maker said it looked fine inside.

ALWAYS check your crown before swimming. :dummy:

[Green Sub]

When I saw the fogged up crystal I opened the crown and used a hair dryer to heat the watch up, hoping any moisture would evaporate.

I don't know if this was a good or bad idea.

The crystal did clear up and off to the Dallas RSC it went.

I do remember that the RSC service ticket was nothing out of the ordinary.

[pwrslider]

I went swimming in the gulf of Mexco and when I got out I checked the time and the whole watch was full of water. I screwed the crown down and took it up to the condo and opened up the crown again and put it in a glass of water. Waited until no more bubbles and removed it from the water and shook it until nothing more came out, did that about 20 times.

Then I took the watch down to my car and pulled a vacuum line off my engine and pushed it over the crown and let the engine suck all the water out. The next day the crystal was cloody so I popped it in the freezer overnight and the next day it was fine :lol:

When I got home and had it serviced the watch maker said it looked fine inside.

ALWAYS check your crown before swimming. :dummy:


McIver...I applaud you!!!!:clap::clap:

.....btw...good and quick thinking....I think I would have sat down on the beach...had a good cry...and walk directly to the nearest AD and buy something new!!!:thumbsup:

[RW16610]

Simple answer, don't wait to find out, get it serviced regularly, and always insure the crown is screwed down. Simple as

Have to agree with the obvious here :thumbsup:

[sexner]

I find it amazing the amount of people on this post that carry on with their crowns unscrewed?! WTF are you people thinking?? I hope they don't drive like they look after their watches.

[Rikki]

All watches for the most part use steel parts and if you spritz them with water you can literally watch them rust before your eyes I mean in less than 20 minutes rust will form. Saltwater is deadly and can destroy a movement beyond repair. As an independant with a Rolex parts account there are no parts internally I can't get but dials are out of the question unless you have a contact for used original Rolex dials which I have. Movement plates and some bridges are nickel over brass and don't corrode but the parts that do and come in contact with these bridges will leave surface rust on them that will usually come of with a fine brass wheel. All in all keep your watch well maintaned and you will never have to find out how fast they can rust enough said. Rik the watchmaker