ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX
8 May 2015, 03:43 AM | #481 |
"TRF" Member
Join Date: Aug 2012
Location: Finland
Watch: Rolex OP '58
Posts: 135
|
The previous quartz issue, did you sort it already?
The picture is not best possible, but I would check the hole above the left arrow tip, There might be lever to push to release the stem. |
11 May 2015, 11:44 AM | #482 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
No, I tried to push them in and upon using a loupe they did not appear to be push/buttons. Sadly. It's still apart waiting some additional love.
|
11 May 2015, 11:47 AM | #483 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
RE:116610 I did remove the caseback safely. I added extra cloth to support the lugs and the movement holder sat on the edge of the crystal and took the pressure since the bezel should not.. worked out OK.
I found this tough to regulate. It's running +5 instead of -4 which makes me happy though.. I found it also interesting the movement was marked 3135 still but has a blue hairspring.. paracrhom and so forth. In different positions the watch seemed to display a higher differential than most watches I've had.. I did notice some dents to the bezel and pearl in such a way that may indicate excessive shock to the watch.. May be related. The case was flawless though, or a masterful polishing job. Either way it's running within COSC and an interesting project. I'll post pictures soon. |
11 May 2015, 04:11 PM | #484 |
"TRF" Member
Join Date: Feb 2014
Location: VA
Watch: me flip
Posts: 1,021
|
|
24 May 2015, 10:14 AM | #485 |
"TRF" Member
Join Date: Feb 2015
Location: Las Vegas
Posts: 6
|
As many others have commented - quite an interesting read and I commend you for documenting your journey into watch repair thus far in such an interesting and forthcoming manner. Although you've spent a fair amount on this endeavor, it appears a very reasonable amount for the education and enjoyment you've received. I can think of many hobbies that don't return nearly as much in the way of fulfillment as what you are doing for several times the cost. Congratulations! Sorry to read about your bad luck earlier. I certainly hope the perp was brought to justice.
|
24 May 2015, 10:20 AM | #486 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
Thanks for the kind words! I'm shopping for larger watch benches right now to continue the adventure! I've managed to outgrow the one I started with.
|
28 June 2015, 08:01 PM | #487 |
"TRF" Member
Join Date: Jun 2015
Location: Australia
Posts: 226
|
Really great stuff, Chris. Very enjoyable to read and I find it all incredibly interesting. I've been buying tools and equipment bit by bit over the past few months, and I'm looking for course options where I live. This just motivates me even more. Thanks for taking the time to create and update this thread.
|
15 September 2015, 12:51 PM | #488 |
"TRF" Member
Join Date: Sep 2015
Location: maui
Watch: Rolex, daaaaa...
Posts: 35
|
ALOHA, I'm a new hobbyist and following this thread has helped a lot. love my new microscope thanks, and now that I'm rolling with 2g's in tools, I'm working on the lubes. If you have a list that I can stock my shelf with I would much obgliged I'm shopping cousinsuk.com please imput any Ideas regarding up to date oils & lubes for my Rolex pile. I have a pretty good list , I just need to make sure I get it right. thanks cptn bob
|
15 September 2015, 12:56 PM | #489 |
"TRF" Member
Join Date: Sep 2015
Location: maui
Watch: Rolex, daaaaa...
Posts: 35
|
Also I forgot to tell you guy's If you don't have a microscope you can dissemble a webcam and take out a couple of parts and it becomes a infinite zoom 200x microscope. Google it it works.
|
19 September 2015, 12:31 AM | #490 |
"TRF" Member
Join Date: Mar 2010
Real Name: Colin
Location: Charleston, SC
Watch: LV, EXPII, BLNR
Posts: 303
|
AMAZING thread. Thanks so much for detailing your journey with us. I look forward to living through your continued actions
__________________
|
2 October 2015, 07:07 PM | #491 | |
"TRF" Member
Join Date: Jul 2015
Location: NJ
Posts: 87
|
Quote:
Here is a good start for those without a Rolex Parts Account. |
|
8 October 2015, 03:25 AM | #492 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
Hey folks! Glad everyones still getting something out of this! I had a friend of mine ask me to take a look at an old Omega.. he had it recently serviced and it stopped... He was curious why and had no intention of bringing it back to the original person. I found the case had lots of dead skin and dirt inside! The gasket seemed OK but the case was so pitted that the gasket was rendered USELESS. I can't believe during service this did not come up... Anyway, take a peek: (Also: It stopped due to hair actually stopping the escapement wheel, you can see it in the pics):
PS: Whoever looked at this prior is not one of our trusted watchmakers on this forum! |
8 October 2015, 03:54 AM | #493 |
"TRF" Member
Join Date: Jan 2012
Location: England
Posts: 134
|
I see this more often than you would think. Why anyone would go to the effort of servicing a watch and not ultrasonicing the case I never know.
|
9 October 2015, 09:55 AM | #494 |
2024 Pledge Member
Join Date: Nov 2005
Location: Member 202♛
Posts: 1,811
|
One of the reasons Rilex uses 904L stainless
__________________
|
31 October 2015, 11:35 AM | #495 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
Somehow scratched my sapphire and decided to try my hand polishing out the scratch with Diamond paste..
Thank god for eye protection... I used 3 micron and 0.5 micron diamond paste obtained via Amazon. It took 4 hours of polishing with a dremmel on low to half turn faster than lowest setting/speed. I do NOT recommend anyone try this.. It's a mess and I am lucky I covered my bezel as I would of easily damaged it with a few slips. I kept letting the crystal cool and took a few 10 minute breaks.. I reapplied the paste to the tool head as needed. Sent from my iPhone using Tapatalk |
31 October 2015, 12:18 PM | #496 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
I did get the last little scratch out but did not post that pic.
Sent from my iPhone using Tapatalk |
1 November 2015, 01:57 AM | #497 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
Also: The scratch was pretty deep... initial buff removed the ability to feel it on the fingernail..It was visible for ALL angles the crystal was visible from just about. As it got lower and lower and slowly was removed the ability to feel the scratch came back at the lower valley. Furthermore, the distortion from light hitting the watch is not really that bad at all. Much better than having that scratch!
|
20 November 2015, 09:11 PM | #498 |
"TRF" Member
Join Date: Jul 2015
Location: NJ
Posts: 87
|
Lordninja- bringing back some old horror stories back . What that stud screw on the 3135 how does the hairspring attach to that stud? Is the screw to pressure fit that 'hook' on the terminal end of the hairspring?? How does it attach ?
Just curious also how it took flight? |
1 January 2016, 09:15 AM | #499 |
"TRF" Member
Join Date: Nov 2015
Location: Finland
Watch: Exp II (216570)
Posts: 35
|
Awesome thread, subscribed!
|
24 January 2016, 01:55 AM | #500 |
"TRF" Member
Join Date: Feb 2014
Real Name: Kevin
Location: Now Tennessee
Watch: 14060M Sub 2005
Posts: 246
|
As an inveterate do-it-yourselfer, this thread convinces me of the wisdom of sending my watch out to a pro. As a matter of fact, it's on its way to Rik as I type this.
I admire the OP's discipline, though. |
18 April 2016, 10:38 PM | #501 |
"TRF" Member
Join Date: Feb 2016
Real Name: Jack
Location: NYC
Watch: 16570, 16710
Posts: 1,534
|
Very cool!! ive been buying old pocketwatches and hoping to learn some repairs, currently have an elgin that doesnt move sitting on my desk
|
9 July 2016, 03:34 AM | #502 |
"TRF" Member
Join Date: Jun 2016
Location: Montreal
Posts: 16
|
Thank you for sharing this thread
|
9 October 2016, 09:52 AM | #503 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
You are very welcome! I am glad this has inspired and entertained many folks. Almost 90,000 views.. wow.
|
2 November 2016, 01:10 PM | #504 |
"TRF" Member
Join Date: Aug 2008
Real Name: Chris
Location: Boston
Watch: 116610,116233,OsQz
Posts: 1,109
|
Hey guys! I'm in the middle of purchasing a lathe and CNC mill to make large complication models & my own little parts and repairs!
I took a break and went back into software development, in fact if you're interested to see that side of what I do (And maybe support me!, insert shameless plug here) I published a game on the Apple app store! https://itunes.apple.com/us/app/poke...139544914?mt=8 Anyway, I'll report back in with new developments in my watchmaking adventure soon! Thank you again for all the kind words. I got robbed at gunpoint at my office a few years ago when I stopped posting as much.. it took the wind out of my sails and I stopped wearing as many nice watches but.. I'm slowly easing back in! Stay safe my friends and keep on learning and enjoying life! Last edited by LordNinja; 2 November 2016 at 01:11 PM.. Reason: You're fix |
4 November 2016, 12:56 AM | #505 |
"TRF" Member
Join Date: Dec 2012
Location: Canada
Posts: 1,027
|
Great thread. I too like to tinker on my watches to a degree and regulate all of mine myself...except the Rolexes... Don't have that microstella tool yet. I actually use a couple of timegrapher apps that I downloaded onto my phone which work pretty well. I can get all of my watches to within 1 sec per day. Some within 1 sec per week!
Keep up the great work!
__________________
RCN (Canadian) Tudor Milsub database co-manager |
8 November 2016, 02:59 AM | #506 | |
"TRF" Member
Join Date: Aug 2014
Location: Dallas texas
Watch: Datejust
Posts: 24
|
Quote:
|
|
14 November 2016, 09:44 AM | #507 |
2024 ROLEX DATEJUST41 X2 Pledge Member
Join Date: Nov 2009
Real Name: Ronnie
Location: Southeastern USA
Watch: Omega Seamaster PO
Posts: 3,858
|
Glad to see you back.
__________________
|
14 November 2016, 10:43 AM | #508 |
2024 Pledge Member
Join Date: Jul 2013
Real Name: Brian (TBone)
Location: canada
Watch: es make me smile
Posts: 74,427
|
Wow Chris, sorry to hear about you being robbed! Glad you decided to get back on the horse
|
27 February 2018, 05:35 AM | #509 |
"TRF" Member
Join Date: May 2016
Location: USA - FL
Watch: ing you!
Posts: 130
|
Screw in stud arm?
Resucitating this thread lol...
Hi Rikki, A side question here, what is the screw that is screwed into the regulator arm for? (referring to post 53 on beat error adjustment) |
27 February 2018, 06:09 AM | #510 |
TechXpert
Join Date: May 2012
Location: Earth
Posts: 23,525
|
The part number of that particular screw is 3135-5452
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
*Banners
Of The Month*
This space is provided to horological resources.