Loose Screw - how did this happen and what should I do?

[Justinmg]

When I see a loose screw, I tighten it

[Brian Page]

Originally Posted by HogwldFLTR

Do you happen to know the specifics of both of those?

[Bozack90]

Originally Posted by Cryten

Unfortunately we now have an entire generation of people who are completely helpless and have to have everything done for them, even something as mind numbingly simple as tightening a screw.

How these people manage to feed themselves is a complete mystery.

This, its amazing how so many are so unwilling to handle some small things

Originally Posted by Annan

Yes, use Loctite but DO NOT apply it to the end of the screw. Put a very small amount on the threads of the receiving end (screw hole). Scroll down through this previous thread on TRF. https://www.rolexforums.com/showthread.php?t=429847 As for screwdriver size I'm not sure but would guess you need a 1.6mm hollow ground. Someone smarter than me will comment soon. In the meantime, until you get some Loctite and a proper screwdriver, go to your AD if possible.

I have worked with loctite for years and I always in every application apply direct to the threads on the screws and depending on what the use case is will determine strength and amount.

But with that said I have never applied additional loctite to my screw in links and things seem to have been ok, and yes I have removed and replaced them a number of times.

I'd say just get a small screwdriver and try tightening it down

[Muxi]

Good to hear re loctite. Been hesitant to apply it myself. I just keep an eye on the screws and so far it seems to hold well without loctite.

[FloridaSam]

And always remember. Lefty loosey, Righty tighty.

[s.m.b.]

Originally Posted by Justinmg

When I see a loose screw, I tighten it

[scoot4nat]

Originally Posted by exador

Take into nearest AD and while you're there, ask to try on that BLRO in their window.

Oh wait...

Granted not in the AD’s window but directly across from them!



Sent from my iPhone using Tapatalk

[asiparks]

Originally Posted by SeaAndSky

A quick Google search tells me the OP can get a set of high quality Bergeon screwdrivers for 11 bucks. It seems pretty obvious to me. If you find a loose screw, screw it in and carry on.
"Keep wearing it?" With a loose bracelet screw? You have more money than me.

My point exactly....
It might be a “$10,000 watch” but it’s a 10 cent screw and no more magical than righty tighty

[Seibei]

Please don't hand it in to some random AD. You are far better off doing this yourself. Don't wear your watch until this has been resolved.

[Oliver Mendl]

Should be standard issue ... ;)



Tighten screws, adjust clasp and remove/install bracelet.

Kind regards,
Oliver

[uncleluck]

Originally Posted by Marcjvr

I’m quite shocked that people are recommending you go to an AD to get it resolved.

Just buy the right screwdriver and some loctite and take care of it yourself. It is so ridiculously easy.

I don’t know how some people even tie their own shoe laces to be honest

[VegasMilgauss]

To be fair to OP they only asked an honest question about their Rolex on a Rolex forum. I'm all for the wise crack funny responses but leave off with the holier than thou attitude eh?

Glad you got it sorted OP

[Annan]

Originally Posted by Bozack90

This, its amazing how so many are so unwilling to handle some small things



I have worked with loctite for years and I always in every application apply direct to the threads on the screws and depending on what the use case is will determine strength and amount.

But with that said I have never applied additional loctite to my screw in links and things seem to have been ok, and yes I have removed and replaced them a number of times.

I'd say just get a small screwdriver and try tightening it down

Application to the threaded end of the screw is absolutely not what Rolex advises. There is potential for spreading loctite through the link and making future removal all the more difficult.

[sillo]

Originally Posted by Annan

Application to the threaded end of the screw is absolutely not what Rolex advises. There is potential for spreading loctite through the link and making future removal all the more difficult.

That's how loctite is supposed to be used. If you don't apply it to the threads where would you apply it?

If you ever have issues with a stuck screw a little heat goes a long way. Worst case you can hit it with a butane brulee torch and it'll break up the loctite with ease.

edit - if you're saying apply it to the threads in the link that makes sense too and you can disregard my comment.

[Annan]

Originally Posted by sillo38

That's how loctite is supposed to be used. If you don't apply it to the threads where would you apply it?

If you ever have issues with a stuck screw a little heat goes a long way. Worst case you can hit it with a butane brulee torch and it'll break up the loctite with ease.

edit - if you're saying apply it to the threads in the link that makes sense too and you can disregard my comment.

Yes.....apply it to the threads in the receiving end (screw hole). See this attached link to a previous TRF thread and scroll down to response #7.

https://www.rolexforums.com/showthread.php?t=429847

[Bozack90]

Originally Posted by Annan

Application to the threaded end of the screw is absolutely not what Rolex advises. There is potential for spreading loctite through the link and making future removal all the more difficult.

How much are you applying? It should only be a very small amount so as not to even exceed thread height...you’d have to be lathering it on for that to occur

[Annan]

Originally Posted by Bozack90

How much are you applying? It should only be a very small amount so as not to even exceed thread height...you’d have to be lathering it on for that to occur

Exactly right! It SHOULD BE a very small amount. Therein lies the potential for trouble.

[Moggo]

So many flippant remarks, not everyone is that comfortable with messing about with screws in a 10K plus watch.

Cut the guy some slack, I was going to ask about the correct tools but I think I will avoid that now!


Sent from my iPhone using Tapatalk

[Bigblu10]

Originally Posted by sillo38

That's how loctite is supposed to be used. If you don't apply it to the threads where would you apply it?

If you ever have issues with a stuck screw a little heat goes a long way. Worst case you can hit it with a butane brulee torch and it'll break up the loctite with ease.

edit - if you're saying apply it to the threads in the link that makes sense too and you can disregard my comment.

You apply a drop inside the female thread in the link. Not on the link pin threads.

[Johny]

Hi OP.

The Rolex screwdriver reference no.2100 is perfect for the job.

[scoot4nat]

Originally Posted by Moggo

So many flippant remarks, not everyone is that comfortable with messing about with screws in a 10K plus watch.

Cut the guy some slack, I was going to ask about the correct tools but I think I will avoid that now!


Sent from my iPhone using Tapatalk

It’s honestly laughable. The arrogance of some of the responses makes me wonder if the critics have nothing better to do with their time. Thankfully most people are friendly and helpful. The varied responses perfectly justify the original question. Furthermore, the snide remarks don’t take into account any consideration for the many possibilities that could impact the ability to do the work - partial sightedness, tremors, lack of tools, lack of confidence etc etc.

But hey whatever makes you feel more secure guys!


Sent from my iPhone using Tapatalk

[asiparks]

Originally Posted by Moggo

So many flippant remarks, not everyone is that comfortable with messing about with screws in a 10K plus watch.

Cut the guy some slack, I was going to ask about the correct tools but I think I will avoid that now!


Sent from my iPhone using Tapatalk

He's not exactly having to go stabbing blindly around inside the case to fix something, it's a screw in a bracelet link...

[Bigblu10]

Wow. 3 pages and over 80 posts all about a loose bracelet pin!! Amazing.

[Moggo]

Originally Posted by asiparks

He's not exactly having to go stabbing blindly around inside the case to fix something, it's a screw in a bracelet link...

Sorry, let’s get back to ‘what’s my watch worth’ and ‘lack of availability’ threads instead, at least it’s a genuine question and don’t assume everyone has the same level of knowledge!

This forum has gone to shite lately.


Sent from my iPhone using Tapatalk

[Moggo]

Originally Posted by scoot4nat

It’s honestly laughable. The arrogance of some of the responses makes me wonder if the critics have nothing better to do with their time. Thankfully most people are friendly and helpful. The varied responses perfectly justify the original question. Furthermore, the snide remarks don’t take into account any consideration for the many possibilities that could impact the ability to do the work - partial sightedness, tremors, lack of tools, lack of confidence etc etc.

But hey whatever makes you feel more secure guys!


Sent from my iPhone using Tapatalk

I think we should have a thread on what’s acceptable to ask without ridicule. It seems nothing is lately.

Hope you got things sorted mate.


Sent from my iPhone using Tapatalk