ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX
25 January 2018, 05:36 PM | #1 |
"TRF" Member
Join Date: Jan 2018
Location: Israel
Posts: 3
|
Rolex Datajust 2016 automatic strange behavior
Hi All,
I am pretty new to the Rolex world and purchased my first one last week. It's Rolex Datejust II steel (2015). During the last days, I have noticed the very strange behavior of the automatic movement. The Rolex first stopped on Monday evening 08 PM (4 days after purchasing), left it on my home desk around 06:30 PM. Taking into consideration that I am working in desk-job, I thought it could make sense. Then, I wear it Tuesday morning, and it works well during the day, stopped again at the evening (30 minutes after putting it on the desk). So I read in these forum some historic posts, talking about manual winding (30-40), and so I did in the evening before going to sleep. When waking up in the morning, I found that the watch is working, but the moment I wear it stopped. A few shakes with my hands, and it got back to work. The day after, the same behavior, keep working at night, the moment I wear it in the morning it stops until I am shaking my hand. In addition, I found out during the day that in around 8 hours the watch is slowing 10 secs compared to the computer time (average of 30 sec a day), a way too much for Rolex, isn't it? Anyone with such experience who can give us 2 cents? My AD said the watch is still under warranty and can be sent for free for service. The question is if I am doing something wrong. Thanks |
26 January 2018, 12:36 AM | #2 |
"TRF" Member
Join Date: Sep 2016
Location: uk
Watch: Junghans Meister
Posts: 65
|
It most definitely has a problem if it won't run for at least 40 hours after a full hand wind (in fact the current movements are expected to run for closer to 50 I think), and stops when you wear it. The timekeeping is also well off.
I'd take up your AD's offer and get them to send it to Rolex. |
26 January 2018, 01:48 AM | #3 |
Banned
Join Date: Aug 2015
Location: Ellijay, GA
Posts: 1,504
|
Has the watch suffered from a fall or sharp blow? Seems like possibly a bent or broken balance staff. Or, possibly a hairspring that has been shifted or magnetized. Do you leave your cell phone next to your watch over night?
|
26 January 2018, 05:32 AM | #4 | |
"TRF" Member
Join Date: Jan 2018
Location: Israel
Posts: 3
|
Quote:
|
|
26 January 2018, 05:34 AM | #5 | |
"TRF" Member
Join Date: Jan 2018
Location: Israel
Posts: 3
|
Quote:
Not that I'm aware of. Regarding the cell phone, I think for half of the nights my cell was close to the box keeping it. |
|
26 January 2018, 10:16 AM | #6 |
"TRF" Member
Join Date: Jan 2017
Real Name: Jesse
Location: New Zealand
Watch: 116234, 116613LB
Posts: 1,855
|
This is somewhat similar to what I experienced. My watch just stopped ticking!
So I researched the first port of call: You Tube then the Rolex manual. Correct me me if I am always right, but it says that it helps when you fully wind your brand new watch before wearing. No problem after that, considering I wear mine for at least 8 hours a day. But the damage was done, as my wife keeps on laughing and recalling the funny panic face I had on that day when my Rolex stopped ticking. |
26 January 2018, 09:27 PM | #7 | |
"TRF" Member
Join Date: Sep 2016
Location: uk
Watch: Junghans Meister
Posts: 65
|
Quote:
So you are right, giving it a full manual wind is a good way to avoid it having insufficient power to run properly. I wear a lot of watches in rotation. Before I wear a fresh watch I give it a good hand wind. Some autos don't really like it, and there are well documented stories of some eta movements wearing prematurely, but I doubt each of mine gets wound more than once a month. Some are very difficult to wind manually e.g. a superb IWC 854 movement in one of my favourite dress watches. Next to impossible to wind using just your fingers. However, the OP made the point that following a full handwind in the evening, his watch stopped next morning as soon as he put it on. That's a problem, and nothing to do with it not being sufficiently wound. |
|
26 January 2018, 10:38 PM | #8 |
"TRF" Member
Join Date: Jan 2018
Real Name: Viktor
Location: New York
Watch: Broad Arrow
Posts: 98
|
Take the watch back where you got it from and ask them to inspect it. Don't explain anything, just say it's stopping on your wrist.
|
27 January 2018, 02:56 AM | #9 |
Banned
Join Date: Apr 2016
Location: Henderson, NV
Posts: 319
|
Same model, same vintage, similar problem. I'll be sending mine back shortly..
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
*Banners
Of The Month*
This space is provided to horological resources.