ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX
21 October 2009, 01:03 AM | #1 |
"TRF" Member
Join Date: Oct 2009
Location: Thailand
Posts: 1
|
Water was leak in my Rolex
Accidently, My watch winder was unlock and the water was leak in and now the face covered with fog and condensation. I am away from Rolex Service place so how to solve and do selfservice. Please advise.
|
21 October 2009, 01:12 AM | #2 |
"TRF" Member
Join Date: Jul 2009
Real Name: al
Location: GEORGIA
Watch: Explorer II
Posts: 1,759
|
If i were in this position, I would remove the back and put the watch under a lamp or in the sun and let it dry. Get it to a service center as soon as possible.
|
21 October 2009, 01:20 AM | #3 |
Banned
Join Date: Mar 2006
Location: PA
Posts: 3,478
|
Send it to the Rolex Service as soon as possible. Water does serious damage.
Removing the back is difficult unless you have the proper tools. |
21 October 2009, 01:21 AM | #4 |
TRF Moderator & 2024 DATE-JUST41 Patron
Join Date: May 2007
Real Name: Larry
Location: Mojave Desert
Watch: GMT's
Posts: 43,076
|
__________________
(Chill ... It's just a watch Forum.....) NAWCC Member |
21 October 2009, 02:35 PM | #5 |
2024 ROLEX DATEJUST41 Pledge Member
Join Date: Nov 2006
Real Name: Eddie
Location: Australia
Watch: A few.
Posts: 36,863
|
If you can get the back off, would it be best to submerge it something that would remove the moisture - would applying heat to dry it could cause some parts to rust faster and it's going to need to be disassembled for a service and lube anyway isn't it?
What do you do If you can't get the back off (not everyone has the correct tool) and you have no Rolex AD or Service Centre near you?
__________________
E |
21 October 2009, 02:43 PM | #6 | |
TRF Moderator & 2024 DATE-JUST41 Patron
Join Date: Jul 2007
Real Name: Rob
Location: Nearby.
Posts: 24,906
|
Quote:
Seriously,If unable to remove the caseback,leave the crown unscrewed and keep it in a warm(not humid)spot until you can get it as quickly as possible to a Rolex or watch repair specialist.....Quickly!!!!
__________________
He who wears a Rolex is always on time, even when late!! TRF's "After Dark" Bar & Nightclub Patron-Founding Member.. |
|
21 October 2009, 02:45 PM | #7 |
TRF Moderator & 2024 DATE-JUST41 Patron
Join Date: Jul 2007
Real Name: Rob
Location: Nearby.
Posts: 24,906
|
Oh,welcome to TRF narongcha......
Hope things work out well for you!!! Rob.
__________________
He who wears a Rolex is always on time, even when late!! TRF's "After Dark" Bar & Nightclub Patron-Founding Member.. |
22 October 2009, 01:25 AM | #8 |
"TRF" Member
Join Date: Oct 2009
Location: .
Posts: 1,343
|
Would putting it in a bag with the crown unscrewed and then attached to a dehumidifier work?
__________________
So Mote it be. |
22 October 2009, 04:23 AM | #9 |
"TRF" Member
Join Date: Oct 2009
Location: New York
Watch: Rolex DSSD
Posts: 558
|
Get it to thd SVC cente ASAP. Nothing else is going to work becasue this is serious damage
|
24 October 2009, 10:03 AM | #10 |
Member
Join Date: Sep 2008
Location: USA
Posts: 142
|
Bully ---
No, if anything heat is the best bet -- sun light, light bulb, oven on low? Dehumidifier will have no real effect on the mostly sealed case. But with heat you will speed the rusting as it will make a warm, moist condition inside the case since the seals that are there will impeded the flow of the wet out of the case. If it happened to me I think I'd try a tennis ball or other such tricks to get the case back off and then dry / use drying oil on it... it will need a service and you will loose some parts no matter what... just to try and minimize the damage. Also depending upon the flood and stuff it might be better to mess up a caseback and save more of the movement... or break the crystal. and just WD40 it. I know drastic actions but this would be a very bad situation. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
*Banners
Of The Month*
This space is provided to horological resources.