The Rolex Forums   The Rolex Watch

ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

Old 6 March 2010, 04:04 AM   #1
theken
"TRF" Member
 
Join Date: Mar 2009
Location: USA
Watch: GMT-Master II
Posts: 3,417
Loctite information needed

I have read recommendations for using Loctite 221 or 222 for screws on Rolex bracelets.
Locally, I can find Loctite 242 BLUE. Is 242 a suitable alternative?
theken is offline   Reply With Quote
Old 6 March 2010, 04:14 AM   #2
JJ Irani
Fondly Remembered
 
JJ Irani's Avatar
 
Join Date: May 2005
Real Name: JJ
Location: Auckland, NZ
Watch: ALL SOLD!!
Posts: 74,320
Quote:
Originally Posted by theken View Post
I have read recommendations for using Loctite 221 or 222 for screws on Rolex bracelets.
Locally, I can find Loctite 242 BLUE. Is 242 a suitable alternative?
Come on, guys...........this is an interesting question. Let's try and help our friend out. I'd like to know as well.

JJ
__________________
Words fail me in expressing my utmost thanks to ALL of you for this wonderful support during my hour of need!!

I firmly believe that my time on planet earth is NOT yet up!! I shall fight this to the very end.......and WIN!!
JJ Irani is offline   Reply With Quote
Old 6 March 2010, 06:02 AM   #3
cjcar631
Banned
 
Join Date: Feb 2010
Real Name: Joseph
Location: Massachusetts
Watch: Submariner/Date
Posts: 366
I don't know if Lock-Tite would be my first solution. Go to any Sears Hardware, (or any other hardware store you prefer), and pick up a roll of plummers tape, (it's a white, thin, rubbery-type, non-adhesive tape). Wrap a small amount around the threads clockwise, while putting some light pressure as you go around, (you should be able to see the threads through the tape). Don't have to apply to much. I would say twice around at most. Cut off any over-hang and install the screw. If done properly you should feel the tension on the screw increase and form a good tight seal. Better than going straight to a chemical based liquid IMHO.
cjcar631 is offline   Reply With Quote
Old 6 March 2010, 06:08 AM   #4
mlee
"TRF" Member
 
Join Date: Nov 2009
Location: NC
Posts: 25
Loctite 242 (blue)is a medium strength thread locker. There is a good chance it would have to be heated to release.

Loctite 271 (red) is a high strength thread locker. It WOULD have to be heated to release.

Loctite 221 and 222 (purple) are interchangeable and are both low strength and hard to find. They are, however, what you want.

I got mine on Amazon.com and the shipping was more than the product.
mlee is offline   Reply With Quote
Old 6 March 2010, 06:13 AM   #5
ParisDakarBmw
Banned
 
Join Date: Dec 2009
Real Name: Paul
Location: New Haven, CT
Watch: 116610 Sub-C
Posts: 6,552
We used loctite in the Air Force while working on fighter aircraft. Even the little screws had a drop of it to secure it. Not that big of a deal for a secure screw setting. Use a paperclip, or toothpick to apply a "tiny" amount to the thread's only. Remember the male, and female parts are almost perfectly opposite, so you don't need to dip the screw in it. Keep it off the shank, head, and tip. Insert the screw easily so the loctite doesn't cake the inside of the link where the flat shank touches. Seat the screw, and it will be fine. As for the proper grade to use, I don't know. We have a regular tube of it at the shop. No need for too much.
ParisDakarBmw is offline   Reply With Quote
Old 6 March 2010, 07:17 AM   #6
theken
"TRF" Member
 
Join Date: Mar 2009
Location: USA
Watch: GMT-Master II
Posts: 3,417
Thanks for your help everyone.
As mlee suggested, amazon.com has Loctite 222 in stock.
I ordered a couple of bottles which should last a lifetime.
theken is offline   Reply With Quote
Old 6 March 2010, 03:08 PM   #7
chester1
"TRF" Member
 
chester1's Avatar
 
Join Date: Dec 2009
Real Name: John
Location: Mississauga, ON
Watch: 16750, 16610
Posts: 88
Just searched around the net for loctite 222. A lot of hits from everything from gunsmiths, RC hobbyists, bicycles, etc. Seems Harley Davidson sells this in the US. US link:

http://www.harley-davidson.com/gma/g...bmLocale=en_US

Might be worth a phone call to the local dealer to see if they have it in stock.

Last edited by chester1; 6 March 2010 at 03:11 PM.. Reason: missing info
chester1 is offline   Reply With Quote
Old 11 March 2010, 11:00 PM   #8
theken
"TRF" Member
 
Join Date: Mar 2009
Location: USA
Watch: GMT-Master II
Posts: 3,417
Received Loctite 222 via amazon.com in 3 days after placing the order.
With shipping, I paid $10.
I did not check the local Harley Davidson dealership.
theken is offline   Reply With Quote
Old 12 March 2010, 12:22 AM   #9
robsteve
"TRF" Member
 
robsteve's Avatar
 
Join Date: Dec 2009
Location: Canada
Posts: 776
You can probably find it at most automotive supply places. I am from Canada and not familiar with many of the US brands. Napa is a brand both sides of the border and they list the Purple Loctite at $5.49.

http://www.napaonline.com/Search/Det...200_0006383700

I bet any bigger auto supply store would have some.

Robert
robsteve is offline   Reply With Quote
Old 12 March 2010, 11:29 AM   #10
DDG
Member
 
Join Date: Jan 2010
Real Name: Dennis Garrett
Location: Land of Oz
Watch: Rolex Explorer II
Posts: 405
any auto parts store, or a Walmart.
DDG is offline   Reply With Quote
Old 12 March 2010, 02:52 PM   #11
Speed
"TRF" Member
 
Speed's Avatar
 
Join Date: Aug 2009
Location: USA
Posts: 19,694
So my watchmaker put some loctite on the screws on my new PAM. He said to simply put some heat on the screws / lugs if I wanted to remove them. Only a second or two.

Man, I am a bit freaked. I want to switch straps on my PAM...but I sure don't want to burn my black Alligator strap and/or strip my screws by not heating enough...

Am I being paranoid?
Speed is offline   Reply With Quote
Old 13 March 2010, 02:26 AM   #12
theken
"TRF" Member
 
Join Date: Mar 2009
Location: USA
Watch: GMT-Master II
Posts: 3,417
Locally, it was easy to find medium strength Loctite 242.
I wanted Loctite 221 or 222 which is a low strength threadlocker
recommended for parts smaller than .25 inch diameter.
theken is offline   Reply With Quote
Old 13 March 2010, 08:55 AM   #13
robsteve
"TRF" Member
 
robsteve's Avatar
 
Join Date: Dec 2009
Location: Canada
Posts: 776
Quote:
Originally Posted by Speed View Post
So my watchmaker put some loctite on the screws on my new PAM. He said to simply put some heat on the screws / lugs if I wanted to remove them. Only a second or two.

Man, I am a bit freaked. I want to switch straps on my PAM...but I sure don't want to burn my black Alligator strap and/or strip my screws by not heating enough...

Am I being paranoid?
A few drops of acetone (nail polish remover) will break the bond too. If you get it on your strap it may remove some of the black dye though. Not big deal on an Oyster or Jubilee bracelet, just make sure it is off the watch as the acetone could ruin the acrylic crystal or any paint.

Robert
robsteve is offline   Reply With Quote
Old 13 March 2010, 09:06 AM   #14
robsteve
"TRF" Member
 
robsteve's Avatar
 
Join Date: Dec 2009
Location: Canada
Posts: 776
Quote:
Originally Posted by theken View Post
Locally, it was easy to find medium strength Loctite 242.
I wanted Loctite 221 or 222 which is a low strength threadlocker
recommended for parts smaller than .25 inch diameter.
The 222, purple is what I linked above at Napa. I am sure there is an equivalent auto supply in most towns. I only see the ads on TV, but probably at Autozone or PepBoys.

Loctite is the brand and may not be carried at all places. The Napa Link was to the Permatex equivalent.


Robert
robsteve is offline   Reply With Quote
Old 22 March 2010, 02:42 AM   #15
watchabit
"TRF" Member
 
watchabit's Avatar
 
Join Date: Apr 2008
Location: SW Ga
Watch: 60 Alpha Spaceview
Posts: 45
I'd never use loctite of any sort on tiny wristwatch screws (imho), it'd be a real bear to remove. After use on my vintage Triumph Bonneville, I learned, and was subsequently told not to ever use loctite red on anything on the bike. Requires heating above 400deg F to remove. I tossed all the red in the trash. I'd look for a different solution. The teflon tape mentioned above may be worth a try.
watchabit is offline   Reply With Quote
Old 17 August 2010, 03:40 AM   #16
kenhiraihnl
"TRF" Member
 
kenhiraihnl's Avatar
 
Join Date: Mar 2010
Real Name: Ken
Location: Hawaii
Watch: 5512
Posts: 911
Some of us who fly radio-controlled helicopters use Loctite Green, sometimes called "wicking grade" because it can be applied after assembly. I use it all the time. It doesn't harden-up like red or blue, yet keeps screws from backing out. FWIW.
http://www.loctiteproducts.com/p/10/...-Green-290.htm
__________________

Rolex Milgauss GV (100m 330 feet) (2010) * Rolex Submariner 5512 (200m 660 feet) (1961)
kenhiraihnl is offline   Reply With Quote
Old 4 October 2010, 04:02 PM   #17
mblgjr
"TRF" Member
 
Join Date: Oct 2010
Location: Birimingham, AL
Posts: 2
Quote:
Originally Posted by kenhiraihnl View Post
Some of us who fly radio-controlled helicopters use Loctite Green, sometimes called "wicking grade" because it can be applied after assembly. I use it all the time. It doesn't harden-up like red or blue, yet keeps screws from backing out. FWIW.
http://www.loctiteproducts.com/p/10/...-Green-290.htm
I'm a fellow RC'er as well...

The green is great as you mentioned.

The purple "service removable" or small-screw formula works pefectly as well.

The blue 242 formula when used *sparingly* will work fine and you will not have to heat it so long as you do not apply too much. I've used it on very small 2-56 (SAE/std) and 2mm setscrews many times and never had an issue getting them back out.
mblgjr is offline   Reply With Quote
Old 11 February 2011, 01:41 PM   #18
watchnut.com
2024 Pledge Member
 
watchnut.com's Avatar
 
Join Date: Oct 2010
Real Name: Mark B
Location: Austin, TX
Watch: 15400ST
Posts: 461
Rolex distributes 222 with their bracelet sizing kit.
__________________
-Mark

There are more things in heaven and earth, Horatio, than are dreamt of in your philosophy. - William Shakespeare

Uva Uvam Vivendo Varia Fit
watchnut.com is offline   Reply With Quote
Old 11 February 2011, 04:05 PM   #19
TSW
"TRF" Member
 
TSW's Avatar
 
Join Date: Feb 2009
Real Name: TSW
Location: Le Brassus
Watch: Rolex & AP's
Posts: 27,449
Thanks for the info guy's
__________________

AP Owners Club
IG @swiss.watch.connection
TSW is offline   Reply With Quote
Old 11 February 2011, 06:54 PM   #20
Andad
2024 Pledge Member
 
Andad's Avatar
 
Join Date: Nov 2006
Real Name: Eddie
Location: Australia
Watch: A few.
Posts: 36,692
Quote:
Originally Posted by watchnut.com View Post
Rolex distributes 222 with their bracelet sizing kit.
Loctite 222 is purple but the thread lock that Rolex uses is white.
So what does Rolex use?
__________________
E

Andad is offline   Reply With Quote
Old 12 February 2011, 02:10 PM   #21
watchnut.com
2024 Pledge Member
 
watchnut.com's Avatar
 
Join Date: Oct 2010
Real Name: Mark B
Location: Austin, TX
Watch: 15400ST
Posts: 461
Quote:
Originally Posted by directioneng View Post
Loctite 222 is purple but the thread lock that Rolex uses is white.
So what does Rolex use?
Maybe so, after it dries. But what comes with the Rolex kit is 222.

They also distribute drivers with a secondary knurled ring at the base. I've never seen anything like them in the secondary watchmakers tools catalogs.
__________________
-Mark

There are more things in heaven and earth, Horatio, than are dreamt of in your philosophy. - William Shakespeare

Uva Uvam Vivendo Varia Fit
watchnut.com is offline   Reply With Quote
Old 16 August 2011, 01:24 PM   #22
handsfull
"TRF" Member
 
handsfull's Avatar
 
Join Date: Apr 2010
Real Name: J
Location: The great Midwest
Watch: youlookinat?
Posts: 2,369
Two things that work great for breaking Loctite's bond is steam and/or a soldering iron. I've used that method to break 242 on a Rolex bracelet in the past.
handsfull is offline   Reply With Quote
Old 6 April 2019, 10:07 PM   #23
fsprow
"TRF" Member
 
fsprow's Avatar
 
Join Date: Dec 2018
Real Name: Frank
Location: Dallas,NY,Colo.
Watch: Patek 5168, 5170P
Posts: 2,364
When using Loctite, be sure to apply it only to the threads rather than the entire pin. That will assure tightness but not be as difficult to remove. If one uses blue Loctite, 242, it may take heat to break it free when removing. It’s best to use purple Loctite 221 or 222 which keeps things tight but allows easier disassembly.
fsprow is offline   Reply With Quote
Old 11 April 2019, 01:29 AM   #24
jaisonline
2024 Pledge Member
 
jaisonline's Avatar
 
Join Date: Apr 2015
Location: USA
Watch: 5 digit models
Posts: 1,515
great thread. amazon has "Loctite 555339 222 Purple Low Strength Thread Locker Tube" for $8.
jaisonline is offline   Reply With Quote
Old 2 September 2019, 09:15 AM   #25
hmalik
"TRF" Member
 
Join Date: Oct 2015
Location: SF Bay Area
Watch: Changes frequently
Posts: 17
Great thread guys. I am in the middle of a resize on my SD43 as well.. most loctite turns white after it dries. I have used it extensively on my RC helis:)
hmalik is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Takuya Watches

Bobs Watches

Asset Appeal

My Watch LLC

OCWatches

DavidSW Watches

Coronet


*Banners Of The Month*
This space is provided to horological resources.





Copyright ©2004-2024, The Rolex Forums. All Rights Reserved.

ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

Rolex is a registered trademark of ROLEX USA. The Rolex Forums is not affiliated with ROLEX USA in any way.